Dry mixed thin layer masonry mortar is made of polymer, organic additives and other substances in a certain proportion by a specific process. The common application is the wall we often see. We can't do it without this material. What are its performance characteristics? Jinan plastering mortar manufacturer to introduce you.

　　薄層砌筑砂漿產品性能特點：

　　Performance characteristics of thin layer masonry mortar:

　　一、薄層砌筑砂漿產品特點：

　　1、 Product features of thin layer masonry mortar:

　　使用起來很方便?？梢杂们逅?dāng)嚢琛Ｋ哂懈弑Ｋ?、高粘結強度、高耐候性、良好的抗裂性、低收縮性、防火隔熱性。

　　It's very convenient to use. It can be stirred with clear water. It has high water retention, high bonding strength, high weather resistance, good crack resistance, low shrinkage, fire and heat insulation.

　　二、薄層砌筑砂漿適用范圍：

　　2、 Application scope of thin layer masonry mortar:

　　薄層砌體及抹灰層厚度一般為3-5mm，抹灰厚度不得超過8mm。

　　The thickness of thin layer masonry and plastering layer is generally 3-5mm, and the plastering thickness shall not exceed 8mm.

　　薄層砌筑砂漿

　　Thin layer masonry mortar

　　三、抹灰工藝：

　　3、 Plastering process:

　　門窗框四周填縫→墻基面清理→掛直、方正、抹餅、找平→墻面濕潤（內濕外干）→薄層砌筑砂漿施工→養護→驗收。

　　Caulking around the door and window frame → cleaning of the wall foundation surface → hanging straight, square, plastering and leveling → wall wetting (internal wetting and external drying) → thin layer masonry mortar construction → maintenance → acceptance.

　　a）清理基層表面雜物。基層應清潔、不松散、無灰塵和油脂。松動、開裂的部位應事先鑿除修補，以免影響粘結強度。夏季，當施工或基礎墻比較干燥時，可先適當澆水，使其內濕外干。

　　a) Clean the sundries on the surface of the base course. The base course shall be clean, not loose, free from dust and grease. The loose and cracked parts shall be chiseled and repaired in advance to avoid affecting the bond strength. In summer, when the construction or foundation wall is relatively dry, it can be properly watered first to make it wet inside and dry outside.

　　b）剪力墻界面應在基礎處鑿毛。提前用高壓水槍沖洗清除界面浮灰，次日進行薄層抹灰施工?；妆砻娌恍枰M(jìn)行界面粗化。

　　b) The shear wall interface shall be roughened at the foundation. One day in advance, use high-pressure water gun to wash and remove the floating ash on the interface, and carry out thin-layer plastering construction the next day. The interface coarsening is not needed on the surface of substrate.

　　c）薄層抹灰施工時，宜一次成活，厚度不大于5mm。

　　c) During the thin layer plastering construction, it is better to survive once, and the thickness is not more than 5mm.

　　d）當與不同材料連接時，應采用耐堿玻璃纖維網處理。

　　d) When connecting with different materials, alkali resistant glass fiber mesh shall be used.

　　e）地表水收集后，應及時進行表面處理。

　　e) After the surface water is collected, the surface treatment shall be carried out in time.

　　f）薄層砂漿抹面施工完成后，即可自然養護。當環境異常干燥時，可以通過澆水來治愈。

　　f) After the construction of thin-layer mortar plastering is completed, it can be cured naturally. When the environment is abnormally dry, it can be cured by watering.

　　以上是濟南抹面砂漿廠家小編為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.wodeapartment.com

　　The above is the relevant content introduced by Jinan plastering mortar manufacturer. If you want to know more, please visit the website: http://www.wodeapartment.com