石膏找平顧名思義就是使用石膏板或是石膏粉與膠調和進行墻面或是天花表面不平整范圍的填平工作。這種方法可以進行局部找平且不需要將地面抬高，施工起來比較方便，價格相對來說較為便宜。下面濟南石膏粉廠家為您分享：

Gypsum leveling, as the name suggests, refers to the use of gypsum boards or gypsum powder mixed with glue to fill and level the uneven areas of the surface of walls or ceilings. This method can perform local leveling without raising the ground, making construction easier and relatively inexpensive. The following gypsum powder manufacturers in Jinan share with you:

先對墻面進行清理。如果墻面有裂縫、孔洞等情況的話，可以先嵌入石膏粉將它們填補平整。

Clean the wall first. If there are cracks, holes, etc. in the wall, you can first insert gypsum powder to fill them flat.

涂刷界面劑，防止基層開裂。使用滾筒均勻涂刷，陰陽角區域用涂刷滿漿，涂刷之后注意保持清潔。

Apply interfacial agent to prevent cracking of the base layer. Use a roller to evenly brush, and the internal and external corner areas are coated with paste. After brushing, pay attention to keeping them clean.

防開裂處理。已經開裂的區域先做修補，使用抹刀開八字縫，用石膏刷清掃粉塵，直接鋪貼牛皮紙，涂刷石膏，再使用網格布鋪滿墻面，使兩塊布之間搭接嚴密，重新疊加部分不低于50mm。

Anti cracking treatment. Repair the cracked area first, use a spatula to open the splay joint, use a gypsum brush to clean the dust, directly apply kraft paper, apply gypsum, and then use a grid cloth to cover the wall surface, making sure that the overlap between the two pieces of cloth is tight, and the re overlapping part is not less than 50mm.

接縫處理。不同材質交接處粘貼接縫時，需要粘貼平整牢固。

Joint treatment. When pasting joints at the junction of different materials, it is necessary to paste them smoothly and firmly.

陰陽角彈線。用水平儀在墻面上彈出水平線、垂直線。和頂棚水平線。用石膏粉將邊角區域不平整的地方刮平，之后確定墻面大面積平整度的控制線。

Snap the lines at the internal and external corners. Use a spirit level to snap horizontal and vertical lines on the wall. And ceiling level. Use gypsum powder to scrape off uneven areas in the corner areas, and then determine the control line for large area flatness of the wall.

粉刷基層。根據已經標記好的控制線，批刮石膏。將石膏粉與清水按照比例調兌、攪拌均勻，并在規定的時間內使用完。如果批刮的厚度不超過10mm，則需要鋪貼一層網格布，之后再批刮一層石膏。

Painting the base layer. According to the marked control line, apply plaster in batches. Mix gypsum powder and clean water in proportion, stir evenly, and use up within the specified time. If the thickness of the batch scraping does not exceed 10mm, it is necessary to lay a layer of grid cloth and then batch scrape a layer of gypsum.

面層施工?；鶎拥氖鄬痈稍镏?，需要在面層涂刷一層石膏，批刮滿漿，并找平粗糙的表面，使面層光滑平整。接縫處理。不同材質交接處粘貼接縫時，需要粘貼平整牢固。

Surface layer construction. After the gypsum layer of the base layer is dried, it is necessary to apply a layer of gypsum to the surface layer, scrape the paste thoroughly, and level the rough surface to make the surface layer smooth and smooth. Joint treatment. When pasting joints at the junction of different materials, it is necessary to paste them smoothly and firmly.

以上就是關于石膏粉局部找平的分享了，每一個工地都是認真負責，干凈整潔。我們一直以來對工地的每一項進度都是嚴格把控的，做到一絲不茍。想要了解更多工藝的，繼續關注我們http://www.wodeapartment.com。

The above is the sharing of partial leveling of gypsum powder. Every construction site is conscientious, responsible, and clean. "We have always strictly controlled every progress on the construction site, and are meticulous.". For those who want to learn more about the process, continue to follow us http://www.wodeapartment.com 。