Puttying is a necessary procedure for decoration, which can make uneven areas on the wall surface smooth and prevent external moisture from corroding the wall. It is an important step in the treatment of the base layer. Today, we will talk about how to apply Jinan putty powder and what to pay attention to when applying putty in batches.
1. Measurement is required before applying putty
刮膩?zhàn)邮┕で?，需要先用尺子來進行測量，看看墻面是否水平，以便于確定刮膩?zhàn)拥姆绞?。刮膩?zhàn)右话闶┕杀榧纯桑粌H讓墻面更加平整，而且能將底色覆蓋掉。如果墻面不平整的地方，則涂刮多遍膩?zhàn)觼磉M(jìn)行找平處理，但每道膩?zhàn)邮┕らg隔應在兩三小時，確保墻面充分干燥。
Before applying putty, it is necessary to measure with a ruler to see if the wall is level, in order to determine the method of applying putty. Puttying is usually done twice, which not only makes the wall smoother but also covers the base color. If the wall is uneven, apply multiple layers of putty for leveling treatment, but the interval between each layer of putty construction should be two to three hours to ensure that the wall is fully dry.
2、膩?zhàn)臃凼┕ば枳龌鶎犹幚?/div>
2. Putty powder construction requires base treatment
檢查基面及基層清理，包括清除墻面砂灰結塊、浮砂及塵土，以提高膩?zhàn)臃鄣氖┕っ婊鶎拥钠秸群透街Γ_?；鏌o污染，無空鼓，無縫隙，無疏松無掉粉現象。
Check the cleaning of the base surface and base layer, including removing sand and ash lumps, floating sand, and dust from the wall surface, to improve the smoothness and adhesion of the putty powder construction surface base layer, and ensure that the base surface is free from pollution, hollowing, gaps, looseness, and powder loss.
3、施工溫度要在5℃以上
3. The construction temperature should be above 5 ℃
施工環境一直都是非常重要的因素，如果環境溫度過低，容易影響到膩?zhàn)又杏袡C(jī)添加劑的溶解，如果添加劑不能充分溶解，或是溶解速度過慢，將影響膩?zhàn)优魏蟮某赡べ|(zhì)量和施工性能。施工環境過熱、過干也不行，膩?zhàn)邮┕みm宜在5℃-35℃的環境下進行。
The construction environment has always been a very important factor. If the environmental temperature is too low, it can easily affect the dissolution of organic additives in the putty. If the additives cannot be fully dissolved or the dissolution rate is too slow, it will affect the film forming quality and construction performance of the putty after scraping. The construction environment is too hot or too dry, and putty construction is suitable to be carried out in an environment of 5 ℃ -35 ℃.
![濟南膩?zhàn)臃? src=]()
4、膩?zhàn)优魏穸仍?.5mm-1mm之間
4. The thickness of putty batch scraping is between 0.5mm-1mm
膩?zhàn)拥呐尾荒芴∫膊荒芴?。太薄的話，膩?zhàn)訉尤菀资^快導致膩?zhàn)映霈F(xiàn)粉化，終會影響涂裝的效果。而膩?zhàn)訉优蔚迷胶?，則其干縮強度越大，越容易開裂。因此，單次膩?zhàn)拥呐魏穸群檬窃?.5mm-1mm之間。
The putty batch should not be too thin or too thick. If it is too thin, the putty layer may lose water too quickly, leading to powdering of the putty and ultimately affecting the coating effect. The thicker the putty layer is scraped, the greater its dry shrinkage strength and the easier it is to crack. Therefore, the optimal thickness for a single batch of putty is between 0.5mm-1mm.
5、膩?zhàn)訑嚢韬梅胖脦追昼?，再攪拌使?/div>
5. Mix the putty and let it stand for a few minutes before mixing and using it
在攪拌后放置一會兒，是為了給膩?zhàn)又械某煞痔峁┏浞秩芙獾臅r間以保證膩?zhàn)拥氖┕ば阅芎秃笃诔赡べ|(zhì)量，避免造成添加劑的浪費。膩?zhàn)釉谡{(diào)制成膏狀后，好在半小時內使用，以免膩?zhàn)幼冑|(zhì)影響施工效果。
After mixing, it is left for a while to provide sufficient dissolution time for the components in the putty to ensure its construction performance and later film quality, and to avoid waste of additives. After the putty is prepared into a paste, it is recommended to use it within half an hour to prevent the putty from deteriorating and affecting the construction effect.
6、底層膩?zhàn)游锤赏覆坏米雒鎸?/div>
6. The bottom layer of putty shall not be dried thoroughly and the surface layer shall not be made
內墻膩?zhàn)臃勰佔訉硬灰诉^厚，一定要等干透方可批第二遍膩?zhàn)?。冬季施工，注意防凍通風干燥，底層膩?zhàn)游锤赏覆坏米雒鎸印?/div>
The inner wall putty powder putty layer should not be too thick. It is necessary to wait for it to dry thoroughly before applying the second layer of putty. During winter construction, pay attention to antifreeze, ventilation, and dryness. If the bottom putty is not fully dry, the surface layer cannot be made.
7、刮膩?zhàn)?，這些部位要貼布處理
7. Apply putty and apply cloth to these areas for treatment
如果使用普通膩?zhàn)?，或耐水膩?zhàn)樱瑒t輕體墻、隔墻板之間接縫處、家具和墻面接縫處、墻面開槽處等部位好采用貼布處理工藝。如果使用彈性膩?zhàn)樱涂梢圆挥觅N布處理，直接批刮即可。
If ordinary putty or water resistant putty is used, the bonding treatment process should be used for the joints between lightweight walls, partition boards, furniture and wall joints, and wall grooves. If elastic putty is used, it can be directly scraped without applying a cloth.
批刮膩?zhàn)硬粌H可以讓墻面更美觀，延長墻壁的壽命，還可以協助房間的防潮，注意以上事項，才能讓發揮膩?zhàn)拥淖饔茫尫课莸玫秸嬲谋Ｗo(hù)。更多相關事項就來我們網站
http://www.wodeapartment.com咨詢！
Applying putty in batches can not only make the walls more beautiful and extend their lifespan, but also assist in preventing moisture in the room. Pay attention to the above matters in order to fully utilize the function of putty and truly protect the house. For more related matters, come to our website http://www.wodeapartment.com consulting service
魯公網安備